The PitStop® Subtalar Implant facilitates the correction of pes plano valgus deformities.
The PitStop® Implant is made of PEEK. This biocompatible and inert polymer is flexible, which allows for placement in the sinus tarsi with better load distribution on bone surfaces versus stiffer materials such as titanium and stainless steel.
Support Materials
Select PitStop Support Collaterals
The PitStop® Features
X-RAY MARKERS
Two X-Ray markers made of tantalum are located at each end of the implant to help guide the positioning of the implant
IMPLANT-INSTRUMENT ASSEMBLY
The easy keyed insertion device allows for a tight assembly between the implant and the instrument.
ANATOMICAL SHAPE
The anatomical shape with the two symmetrical and flattened sides are designed to reduce the compressive constraints and to improve distribution of stress. This may help to decrease incidence of reactive synovitis and improve patient tolerance.
CANNULATED IMPLANT
The PitStop® is cannulated to facilitate and secure accurate positioning of the implant over a guide wire.
LOCK-IN FLANGES
Lock-in flanges, (small blades) are designed to provide primary stability in the sinus tarsi.
SURGICAL TECHNIQUE
INCISION
A 1-3 cm incision is made on the lateral side of the foot in the skin overlying the sinus tarsi.
Blunt dissection with a hemostat to level of joint capsule.
OPTIONAL USE OF VILADOT’S LEVER
The Viladot’s Lever is introduced through the sinus tarsi. Move the lever slightly dorsal / medial and anterior / posterior to dilate the tarsal canal
GUIDE-WIRE INTRODUCTION
Once the talus is positioned on the calcaneus, the 1.6mm Guide-wire is introduced into the axis of the sinus tarsi until the wire is felt on the medial aspect of the hindfoot. Accurate placement may be confirmed with fluoroscopy.
INSERTER* / HOLDER PREP FOR TRIALS
Insert the Internal Holder through the base of the External Holder Fig. A.
Fig. B Then attach the Trial Implant to the end of the External Holder by aligning the pins of the Holder to the holes of the Trial Implant. The flat sides of the Trial Implant and the Inserter handle are aligned.
Fig. C Next screw the Internal Holder through the External Holder into the Trial Implant and tighten.
TRIAL SIZER
The first Trial Implant is placed over the Guide-wire and seated in the sinus tarsi. Hindfoot mobility is assessed and the size may be adjusted accordingly. Correct position of the Trial Implant may be verified by fluoroscopy. It is recommended to advance the leading edge of the Trial Implant close to but not past the talonavicular bisection on the AP view. The corresponding flat surfaces of the Trial and Inserter handle are aligned parallel to the lateral talar process which is an approximate 45° angle to the fibula and the plantar aspect of the foot on the lateral view
The Trial Implant is removed leaving the Guide-wire in place.
INSERTER PREPARATION FOR IMPLANT
As with the trial, theImplant is fixed to the External Holder Fig. D.
Fig. E Then tightened onto the Internal Holder by turning the bottom knob to engage the Implant.
CANNULATED INSERTION
The Inserter is used to “press fit” the Implant in the correct position with a pushing motion. “Do not screw Implant into place.” X-ray markers at each end of the Implant help achieve the adequate depth with fluoroscopy visualization. The corresponding flat surfaces of the Implant and Inserter handle are aligned parallel to the lateral talar process which is an approximate 45° angle to the fibula and the plantar aspect of the foot on the lateral view.
Unscrew the Internal Holder to release the Implant and push with finger pressure to remove the Holder from the Implant.
Hind-foot mobility is assessed to verify adequate correction. The wound should be closed according to surgeon preference.
All content contained herein is furnished for informational purposes only. i2b does not recommend a particular surgical product or procedure suitable for all patients. Each surgeon must evaluate the appropriateness of a device and corresponding techniques based on medical training, clinical judgement and surgical experience. The proper surgical technique and/or procedure are the responsibility of the medical professional. Indications, contraindications, warnings, and precautions are listed in implant packaging insert and should be reviewed carefully by the physician and operating room personnel prior to any proposed procedure. • PitStop, the In2Bones name and logo are trademarks or registered trademarks of i2b-USA or its subsidiaries. Peek-Optima is a polymer produced by and a registered brand of INVIBIO In2Bones USA Memphis TN, 38119 USA / In2Bones SAS, 69130 Ecully – FRANCE – © 2018 In2Bones USA, Memphis, TN – All rights reserved- PTST0518 Rev A 0518
Request a Copy of the Surgical Technique Brochure
Ordering Information
In2Bones – 6000 Poplar Ave., Suite 115
Memphis, TN 38119
Follow @in2bones[TWTR]
Recent Comments